DIGITAL START ADDRESS SELECT
OPTION SELECT
DIGITAL INPUT LEDS
1
16
1
2
4
8
16
128
32
64
TEST
256
ON
12 436578109
DIGITAL INPUT
ANALOGUE INPUTS
0-10V
• Zero setting the working hours and number of times the lamp is switched on
To zero the hours of the lamp’s life (“Bulb hours”) and the number of times it is
switched on (“Bulb strikes”) which are stored in the DMX Receiver microprocessor,
proceed as follows:
1. Set the TEST microswitch (32) to the ON position.
2. Shift the option 1 microswitch (37) from ON to OFF (or from OFF to ON) and vice
versa 3 times within a time of 6 seconds. If the procedure has been carried out
correctly, the three signal control LEDs (30) will light up simultaneously, while the
display (29) will go completely blank. This situation lasts for approximately
5 seconds.
3. Return the TEST microswitch (32) to the OFF position.
• Changing the lamp
Open the re-lamping cover, loosen the
two side ring nuts (34) of the lamp to be
replaced and remove it from its
mountings (35).
Take the new lamp out of its package,
loosen the two side ring nuts (34) and
insert the lamp in its mountings (35).
Finally, screw on the ring nuts.
WARNING: Do not touch the lamp’s
bulb with bare hands. Should this
happen, clean the bulb with a cloth
soaked in alcohol and dry it with a
clean, dry cloth.
IMPORTANT: To distribute the beam of
light uniformly, the lamp needs to be
positioned with the protrusion (36) visible
on the bulb outside the optical axis
of the projector. For this purpose it is
recommended to turn the protrusion
towards the top cover
(19).
32 29
37
30
• Replacing colour filters
Find the filter to be replaced, grip it between your fingers and push it towards the
movable point of anchorage (38) until the filter comes out of the fixed points of
anchorage (39). Bend the filter outwards and take it out. Insert the new filter into the
mobile point (38) and anchor it in the two fixed points (39).
Standard colour filters
Disc 1 Disc 2
Red: 080301/005 Yellow with hole:080323/002
Magenta: 080301/023 Blue with hole: 080323/001
Violet: 080301/004 4 colours: 080324/001
Green: 080301/003 Yellow: 080301/002
Wood: 080301/022 Orange
:
080301/007
Blue: 080301/001 Hot: 080301/020
Pink: 080301/006 Cold: 080301/021
• Replacing metal gobos
Find the gobo to be replaced and delicately press towards the anchorage points (40)
until the gobo comes out.
Take the selected replacement from the holder (41) on the dimmer/stopper/strobe
plate.
To insert the new gobo, position it at the two points of anchorage (40) and, lightly pressing
it, slot it into the remaining points, verifying the levelness of the gobo in its housing.
STANDARD GOBOS - ROTATING GOBO WHEEL
082315/001 082311/005 081311/001 081319/001
STANDARD GOBOS - FIXED GOBO WHEEL
081329/001 081331/001 081330/001 081306/001
OPTIONAL GOBOS
081305/001 081313/001 081315/001 081316/001 081318/001
081321/001 081325/001 081307/001 081326/001 081327/001
MAINTENANCE
4
• Opening and closing the cover
Loosen the knob (33) and remove the re-lamping cover (19).
After maintenance refit the cover (19) and lock the knob (33).
(16 stránky)
(46 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce