Clay-paky PIPER I.C.C. (HTI 150) Uživatelský manuál stáhnout pdf (Strana 2)

DMX 512

RS 232/423

LENS UNITS

BEAM OPENING m

0 5 10 15 20

DISTANCE m

0 0,80 1,60 2,40 3,20

DIAMETER m

1400 370

Objective lens 1:2,5/165mm - Standard dotation

lux

161 90

9°

6005700 232 118

2,5

0,40

7,5

1,20

12,5

2,0

17,5

2,80

HTI 150

0” 16’ 5”

DISTANCE ft in

8’ 2” 24’ 7” 32’ 10” 41’ 49’ 3” 57’ 5” 65’ 7”

0” 2’ 7”1’ 4” 3’ 11” 5’ 3” 6’ 7” 7’ 10” 9’ 2” 10’ 6”

DIAMETER ft in

Objective lens 1:2,2/100mm - Available on request

0 5 10 15 20

0 1,34 2,70 4,05 5,40

500 125

lux

55 32

15°

30'

2000 220 80 41

2,5

0,67

7,5

2,02

12,5

3,37

17,5

4,72

HTI 150

BEAM OPENING m

DISTANCE m

DIAMETER m

0” 16’ 5”

DISTANCE ft in

8’ 2” 24’ 7” 32’ 10” 41’ 49’ 3” 57’ 5” 65’ 7”

0”

4’ 5” 8’ 10”2’ 2” 6’ 8”

DIAMETER ft in

11’ 1” 13’ 3” 15’ 6” 17’ 9”

130 34.4

15.0 8.3655.7530 21.6 11.0

46.5 11.6

5.11 2.97186 20.4 7.43 3.81

GRAPHS SHOWING BEAM DATA AND ILLUMINATION VALUES

PAN

GOBO

COL

TILT

Projectors are wired up to the controller and one to the next using a multicore cable

with 8 wires of 0.25mm

section and a DIN 8 pin 45° plug/socket connector.

RS232/423(PMX) - DMX 512 CONNECTION

TEST

256

128

10987654321

11 12

PA N

TILT

GOBOPA N

COL

THE DIGITAL START

ADDRESS IS THE SUM

OF THE NUMBERS

PRODUCED BY THE

SELECTED SWITCHES

DIGITAL

START

ADDRESS

AND

OPTIONS

SELECT

EG.

RESPOND

C.1 - 4

EG.

RESPOND

C.17 - 20

RUN TEST

SEQUENCE

DMX 512

RS232/423

: 1 = ,2 = SIG - ,3 = SIG +

: 1 = ,2 = SIG ,3 = SIG

DIGITAL INPUT

ANALOGUE

INPUTS 0 - 10V

• Projector address codes (for digital signals)

Each PIPER I.C.C. projector uses 1 control channel. To ensure that different projec-

tors are addressed correctly by the controller, a code must be assigned to each one.

This operation is carried out on each PIPER I.C.C. by setting the microswitches as

indicated in the table below.

Projector selection

Projectors are wired up to the controller and one to the next using two-core screened

cable and Cannon 5 pin XLR type plug/socket connectors.

To connect a DMX line, a terminating plug (5) with a 100Ω resistor wired between pins

2 and 3 must be fitted to the last projector connected in series; the plug is not requi-

red when using an RS232/423(PMX) signal.

The wires must not come into contact with each other or with the metal casing

of the plug.

The casing of the plug/socket must be connected to the screen and to pin 1 of

the connectors.

Having completed the operations described above, press the on/off switch (6). Check

that the lamp comes on and that the auto-reset sequence starts.

SIGNAL

SCREEN

SIGNAL

DMX

512

SIGNAL

SCREEN

SIGNAL

RS232/423

(PMX)

Setting the TEST switch to the ON position for a few seconds with the projector

powered-up, an auto-reset routine is carried out. Leaving the TEST switch at the ON

position for a longer period, a full self-test program will be completed; once the ope-

ration has terminated, return the switch to the OFF position.

• Alignment procedure

Loosen the knobs (3) and

manoeuvre the projector on the

bracket (2) until the beam is

directed at centre stage and

then retighten the knobs (3).

• Adjusting the lens

Move the lens (7) back and

forward until the projected image

is satisfactorily focused, then

tighten knob (8).

POSITIONING THE PROJECTOR

CHANNEL FUNCTION

Projector 1 - Channels 1

OFF

TEST

128

OFF

CODE

OFF

Projector 2 - Channels 2

Projector 3 - Channels 3

Projector 4 - Channels 4

Projector 5 - Channels 5

Projector 6 - Channels 6

Projector 7 - Channels 7

Projector 8 - Channels 8

Projector 9 - Channels 9

Projector 10 - Channels 10

PINK

BLUE

ORANGE

GREEN

VIOLET

YELLOW

RED

WHITE

In the 0% to 50% range of adjustment, the

change of colour in response to the move-

ment of the potentiometer is linear and

continuous, so that the slider can be stop-

ped in intermediate positions to obtain a

two colour beam..

From 50% to 100% the wheel rotates

continuously with speed increasing

steadily from 0 to 300 rpm.

• COLOUR WHEEL - channel 1

CHANNEL

FUNCTION

COLOUR WHEEL

3 78

1 2 3 4

Komentáře k této Příručce

Žádné komentáře

Clay-paky PIPER I.C.C. (HTI 150) Uživatelský manuál Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Clay-paky PIPER I.C.C. (HTI 150)