Clay-paky SHOW BATTEN 100 AS (C71086) PRELIMINARY Uživatelský manuál

1INSTRUCTIONS MANUALCongratulations on choosing a Clay Paky product!We thank you for your choice. Please note that this product,as all the others

10SHOW BATTEN 100 OPTIONS MENU OPTIONS - TILT – INV. TILT Use to switch the Tilt inversion movement (ON) or (OFF) . OPTIONS - TILT – P

11SHOW BATTEN 100 INFORMATION MENU INFORMATION MENU – SYSTEM VERSION Use to view the Appliance release (Application firmware) and Boot rel

12SHOW BATTEN 100 MANUAL CONTROL MENU Use to set a projector control panel channel level to manually control each effect without the need o

MAINTENANCE13SHOW BATTEN 10012 Fuses6.3x32mm 2A-T(p/n 030472)9Continue ➔Fuses replacing - Fig. 9Each Show Batten has 2 fuses associated with the main

SHOW BATTEN 10014Periodic cleaning - Fig. 10To ensure optimal operation and performance for a long time it is essential to periodically clean the part

15SHOW BATTEN 100226(8.90")170(6.69")100(3.94")186(7.32")1000(39.37")Source10x15W LED RGBW Ostar (OSRAM)Led pilot power150WOp

CHANNEL CHANNEL MODE STANDARD EXTENDED 1 RED RED 2 GREEN GREEN 3 BLUE BLUE 4 WHITE WHITE 5 CTO CTO 6 DIMMER DIMMER 7 STROBE S

17SHOW BATTEN 100CHANNEL FUNCTIONS Channel Mode DMX Value Function Standard Extended 1 1 RED 0 - 255 Red colour linearly increase fr

18SHOW BATTEN 100 8 8 MACRO COLOUR 0 - 9 Unused range 10 Red 11 Green 12 Blue 13 Cyan 14 Yellow 15 Magenta 16 White 7000K 17 White 3700K 1

19SHOW BATTEN 100 9 9 ZOOM 0 - 255 Zoom linearly moves from narrow to wide beam 10 10 TILT 0 - 255 Moving batten linearly tilts from -12

2SHOW BATTEN 100• InstallationMake sure all parts for fixing the projector are in a good state of repair. Make sure the point ofanchorage is stable be

CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.itIST007/001 – EN - Rev - P

3SHOW BATTEN 100UNPACKING AND PREPARATION2 x 183102/805 REMOVAL OF THE PROTECTIVE FILM112INSTALLATION AND START-UP3Packing content - Fig. 1IST007/00

4SHOW BATTEN 10012334424Projector installation - Fig. 4The projector can be installed on the floor resting on specific rubber feet, on a truss, on the

5SHOW BATTEN 100CONTROL PANELConnections to the power mains - Fig. 6 DMX 512DMX 5125 PINPower Supply67Connections to the control signal line (DMX) -

6SHOW BATTEN 100Switching on the projector - Fig. 8The projector immediately turns on when the power cord is plugged.Clay Paky SHOW BATTEN 100 Address

Main Menu Level 1 Level 2 Level 3 Choices / Values SET UP DMX Address Standard Address 001 - 503 Extended Address 001 - 463

8SHOW BATTEN 100 Main Menu Level 1 Level 2 Level 3 Choices / Values MANUAL CONTROL Red 000 - 255 Green 000 - 255 Blue 000 - 25

9SHOW BATTEN 100 SET UP MENU SET UP - DMX ADDRESS Use to set the DMX address to be assigned to the projector according to the type of pr